The short answer
How to test for radon: set a short-term kit at least 20 inches above the floor in the lowest lived-in level, close windows and outside doors 12 hours before and during a test of 48 hours or more, then mail it to the lab. EPA says to confirm a result of 4 pCi/L or higher with a second test.
On this page
Should your first radon test be a 2 day kit or a 90 day kit?
Start short. The EPA Citizen's Guide to Radon lists the steps in order: “Step 1. Take a short-term test,” and short-term tests “remain in your home for two days to 90 days, depending on the device.” A long-term test stays in place for more than 90 days, and EPA says it gives “a reading that is more likely to tell you your home’s year-round average radon level.”
The trade is speed against accuracy. Radon levels “vary from day to day and season to season,” per the same EPA guide, so one 2 day reading is a snapshot. The ANSI/AARST protocol for homes (MAH section 5.1) adds that a long-term detector used to judge annual exposure should stay out “a minimum of 6 months over different seasons (one of which is a heating season) or as close to a year as possible.”
Whichever you pick, the EPA Home Buyer's and Seller's Guide to Radon, revised March 2024, sets the floor: “all radon tests should be taken for a minimum of 48 hours,” and some devices need longer, “e.g., a 7-day charcoal canister device.” The MAH protocol allows a deployment of no less than 46 hours but says 48 is the target.
Which radon test device measures what, and for how long?
EPA’s EPA Home Buyer's and Seller's Guide to Radon splits devices into two groups. Passive devices “do not need power to function” and are “sent to a laboratory for analysis”; active devices “continuously measure and record the amount of radon or its decay products” and “may cost more” but “may ensure a more reliable result.” The MAH protocol (ANSI/AARST MAH section 2) draws the line by data: a continuous monitor must record reviewable readings in 1 hour increments and be recalibrated periodically, or it counts as a passive device.
| Device | Group | Duration | What it records | Protocol notes | Source |
|---|---|---|---|---|---|
| Charcoal canister | Passive, short-term | Short-term; EPA names a 7 day canister as one needing more than 48 hours | Time-weighted average, read by the lab | Closed house throughout; mail back promptly | EPA HBSG; Citizen’s |
| Charcoal liquid scintillation | Passive, short-term | Short-term window per the maker | Time-weighted average, read by the lab | Same closed-house rules as a canister | EPA HBSG; Citizen’s |
| Alpha track detector | Passive, short or long-term | Short-term, or long-term over 90 days | Time-weighted average, read by the lab | Long-term use: closed house not required past 90 days | EPA HBSG; MAH 5.1.2 |
| Electret ion chamber | Passive, short or long-term | Short-term or over 90 days | Time-weighted average | Long-term use: closed house not required past 90 days | EPA HBSG; MAH 5.1.2 |
| Continuous radon monitor | Active, needs power | At least 48 hours for a decision | Hourly readings that show swings during the test | Some models detect tampering; must be recalibrated | EPA HBSG; MAH 2.3.3 |
Only one published kit price list was found that states what it includes: the National Radon Program Services kit page, run under a cooperative agreement between EPA and Kansas State University, sells a 2 to 4 day short-term kit for $20 and a 3 to 12 month long-term kit for $30, each listed as including all costs with return postage. New Jersey short-term kits carry an extra $10 state radon fee, per the same page. Retail kits cost $10 to $30, according to the Wisconsin Department of Health Services radon page. No published price for a professional continuous monitor test was found for this page, so none is given.

Where does the radon detector go? 20 inches up, 3 feet from a window
Floor first. The EPA Citizen's Guide to Radon says to place the kit “in the lowest lived-in level of the home (for example, the basement if it is frequently used, otherwise the first floor)” in a room used regularly, “but not your kitchen or bathroom.” For a home sale the bar moves lower: EPA’s March 2024 buyer’s guide says the lowest level “that could be used regularly, whether it is finished or unfinished.”
| Rule | EPA consumer guides | ANSI/AARST MAH-2019 | CDC testing page |
|---|---|---|---|
| Height above floor | At least 20 in | At least 20 in (50 cm) | 3 ft, middle of the room |
| Distance from windows and outside doors | Away from drafts | At least 3 ft (90 cm) | Not stated |
| Distance from exterior wall | Away from exterior walls | At least 1 ft (30 cm) | Not stated |
| Distance below ceiling | Not stated | At least 1 ft (30 cm) | Not stated |
| Rooms to skip | Kitchen, bathroom; closet, stairway, hallway, crawl space | Closets, sumps, crawl spaces, isolated kitchens, bathrooms, laundry rooms | Not stated |
The sources do not conflict on height: the CDC radon testing page says to raise the device “three feet off the ground, in the middle of the room,” which clears EPA’s and MAH’s 20 inch minimum. What the CDC page leaves out is the 3 foot gap from openings and the 1 foot gap from an exterior wall in MAH Table 3.3, which keep a draft from diluting the reading.
One location is not always enough. Per the ANSI/AARST protocol, MAH section 3.1 recommends extra test spots for a floor over 2,000 square feet (189 square metres), for each area served by a separate heating and cooling system, and for each foundation type, such as a slab-on-grade room joined to a basement.
What does “closed-house” mean for the 12 hours before a short test?
EPA’s EPA Home Buyer's and Seller's Guide to Radon defines it in one footnote: “keeping all windows closed, keeping doors closed except for normal entry and exit, and not operating fans or other machines which bring in air from outside.” Small exhaust fans run briefly and a radon system’s own fan may stay on. For a test of 2 to 4 days the conditions start at least 12 hours before the test; for 4 to 7 days EPA recommends keeping them throughout.
| Item | Required setting (MAH Table 4-A) |
|---|---|
| Windows | Closed on all levels, including untested floors |
| Exterior doors | Closed except for momentary entry and exit |
| Heating and cooling | Normal operation, thermostat between 65 and 80 F (18 to 27 C) |
| Outdoor-air ventilation for comfort or energy savings | Set to its lowest seasonal setting |
| Whole-house fans | Off |
| Fireplaces | Not burning, unless the primary heat source |
| Clothes dryers, range hoods, bath fans | Avoid excessive use |
If the house was not closed for 12 hours first, MAH section 6.1.2 gives three fixes: postpone the start, stretch the test to 4 days or more after closing up, or, with a continuous monitor, use only the 46 or more contiguous hours recorded after the 12 hour mark. EPA also says not to run a 2 or 3 day test during “unusually severe storms or periods of unusually high winds.”
Per MAH section 6.1.3, if sealing the house would endanger occupants, such as in a heat wave with no cooling, the test is rescheduled rather than run with windows open.
Your first result is 4 pCi/L or higher: second short test or long-term test?
EPA’s EPA Citizen's Guide to Radon gives the branch: “For a better understanding of your year-round average radon level, take a long-term test. If you need results quickly, take a second short-term test.” The higher the first number, the stronger the case for the quick route, and “if your first short-term test result is more than twice EPA’s 4 pCi/L action level, you should take a second short-term test immediately.”
Then decide. A long-term result of 4 pCi/L or more means fix the home, per EPA; with two short-term tests, EPA uses their average. Results near the line are soft: per the EPA Citizen’s Guide, an average of 4.1 pCi/L carries “about a 50% chance” that the year-round average is somewhat below 4. The guide also says the average indoor level is about 1.3 pCi/L and outdoor air about 0.4 pCi/L.
What if the two results land on opposite sides of 4?
MAH section 7 answers it with a ratio. If the higher result is less than twice the lower one, average them; if it is more than twice, the pair is not acceptable and a side-by-side test must be repeated, or a sequential pair needs more testing. The two rows below apply that rule to example numbers.
| Two results | MAH 7.2.2 check | Outcome |
|---|---|---|
| Example A: 3.6 and 4.8 pCi/L, same spot | 4.8 is less than twice 3.6 (7.2), so average them: 4.2 pCi/L | Use the average; fix |
| Example B: 2.5 and 6.0 pCi/L, side by side | 6 is more than twice 2.5 (5) | Not acceptable; repeat the test |
Low readings have a floor too. MAH section 7 notes that results below about 2.0 pCi/L “should normally be interpreted as being lower than the test device can accurately measure,” and cites the World Health Organization’s reference of 2.7 pCi/L (100 Bq/m3). Once a fix is the answer, the system types and contractor checks are on our radon mitigation guide.

How is a radon test done during a home sale, and how is tampering caught?
EPA’s EPA Home Buyer's and Seller's Guide to Radon accepts three short-term options when a sale needs results fast, and says any real estate test “should include steps to prevent or detect interference with the test device.” Two simultaneous tests “would improve the precision”; a sequential pair “would most likely give a better representation of the seasonal average.” MAH section 8.2 makes this time-sensitive protocol the required one for home sales.
| Option | How it runs | EPA decision rule |
|---|---|---|
| Two passive tests at once | Same place, at least 48 hours; MAH puts them 4 to 8 in apart | Fix if the average is 4 pCi/L or more |
| Two passive tests back to back | Second identical device starts as the first ends, each at least 48 hours | Fix if the average is 4 pCi/L or more |
| One continuous monitor | At least 48 hours, hourly records | Fix if the average is 4 pCi/L or more |
EPA lists seven anti-interference steps, among them a device that records frequent readings, a motion detector, tamper-proof window seals and a signed non-interference agreement. The guide adds that disturbing the device or closed-house conditions “may invalidate the test results and is illegal in some states.”
Whether a seller must disclose a radon result is set by state law, not by EPA; the buyer’s guide says only that “some states” require disclosure. Ask a real estate attorney practising in the state whether a past result must go on the disclosure form, and ask the state radon office, listed on the EPA test kit and professional page, which testing protocol the state requires of professionals.
Does living in Radon Zone 3 mean you can skip the test?
No. The EPA Map of Radon Zones, updated 16 September 2026, says homes with high radon have been found in all three zones, that “all homes should be tested for radon,” and that the map “should not be used to determine if a home in a given zone should be tested.” The Citizen’s Guide puts the national picture at nearly 1 in 15 homes above the action level.
| Zone | Potential | Predicted county average indoor level |
|---|---|---|
| Zone 1 (red) | Highest | May exceed 4 pCi/L (150 Bq/m3) |
| Zone 2 (orange) | Moderate | May be 2 to 4 pCi/L (75 to 150 Bq/m3) |
| Zone 3 (yellow) | Low | May be under 2 pCi/L (75 Bq/m3) |
EPA’s Citizen’s Guide says every new home “should be tested for radon after occupancy,” even one built radon-resistant for Zone 1. The passive pipe those features leave behind is the start of a sub-slab depressurization system.
Where can you get a radon kit for $0 to $30, per state and EPA programs, and who counts as a qualified tester?
Start with the state. The CDC radon testing page says “your state may offer free or discounted test kits,” and EPA’s kit page says the same. Two examples, per the agencies’ own pages: the Washington State Department of Health kit form offers a free kit for a home or a non home-based daycare in Washington, and the Wisconsin Department of Health Services radon page, revised 21 October 2026, says many regional Radon Information Centers “provide test kits for free or reduced cost.” Otherwise the Kansas State program kits run $20 and $30, and ship Mondays and Thursdays with 1 to 2 weeks to arrive.
To hire a tester, EPA’s EPA test kit and professional page names the two recognised national credentialing bodies: NRPP, (828) 348-0185, and NRSB, (914) 345-1168. MAH section 8 defines a qualified measurement professional by NRPP or NRSB certification or a state licence, and requires a quality assurance plan under ANSI/AARST MS-QA. The EPA radon standards of practice page lists MAH-2023 as the current homes protocol.
Ask a tester which interference controls they use and whether they will also quote the fix: EPA’s buyer’s guide calls that “a potential conflict of interest” and says some states require a signed waiver. MAH section 2.3.1 also requires decision devices to be listed by NRPP, NRSB or a state program.
When should you test again: 24 hours after a fix, after a remodel, every 2 years?
After a mitigation system goes in, the EPA Consumer's Guide to Radon Reduction (2025) says the post-test “should be done within 30 days of system installation, but no sooner than 24 hours after your system is in operation,” and that retesting “at least every 2 years” is a good idea. MAH section 7.3 adds 12 hours of closed-house conditions before that post-test. Expected prices for the fix itself are on radon mitigation cost.
Other triggers come from EPA and CDC. The EPA Citizen's Guide to Radon says to retest “on that level” if you start occupying a lower floor such as a basement, and to test again “sometime in the future” even below 4 pCi/L. The CDC radon testing page says to test again after major renovations.
Out of scope. This page covers how to measure radon. For the health effects of radon exposure, see the EPA Citizen's Guide to Radon and the CDC radon testing page. Radon is one item in a wider look at indoor air quality testing; related rules sit under Standards.
Questions people actually ask
Can I test for radon myself?
Yes. EPA’s Citizen’s Guide says low-cost do-it-yourself kits are sold by mail and in hardware stores, and the ANSI/AARST MAH protocol encourages homeowners to test with them. MAH recommends a qualified professional, credentialed by NRPP, NRSB or a state program, when the test is part of a real estate sale, where interference controls matter.
What month is radon highest?
No single month is named in the EPA guides or MAH-2019. MAH says homes can be tested at any time of year, but tests run while a heating system operates both day and night are more likely to show a radon problem clearly. A long-term test of 6 months or more that includes a heating season averages out the swings.
What is the most accurate test for radon?
For your year-round exposure, a long-term test over 90 days, which EPA says is more likely to reflect the annual average than a short test. For a quick decision, EPA’s buyer’s guide says two simultaneous tests improve precision and a continuous monitor’s hourly record can reveal abnormal swings or tampering during the 48 hour minimum.
How long do radon test results take?
EPA’s Citizen’s Guide says results should arrive within a few weeks after the kit is resealed and mailed to the lab, and the buyer’s guide says a few days or weeks, with expedited service available from some labs. Record the start and stop times, since the lab needs them, and mail the kit the day the test ends.
How do you test well water for radon?
With a different kit. EPA’s Home Buyer’s and Seller’s Guide says the devices and procedures for water differ from those for air, and advises a water test if your air result is high and your water comes from a private well. Public systems drawing ground water are another source; for those, EPA says to ask the water supplier.
How can you tell if radon is in your house without a test?
You cannot. EPA’s buyer’s guide says radon cannot be seen or smelled and that testing is the only way to find a problem. Zone maps only predict county averages, and EPA says homes with high radon have turned up in all three zones, so a neighbour’s result or a Zone 3 county does not stand in for a test of your home.
Sources
- EPA Citizen's Guide to Radon, United States Environmental Protection Agency, EPA 402/K-12/002. Testing steps, placement, follow-up rule, 4.1 pCi/L example and zones advice. Retrieved 21 November 2026.
- EPA Home Buyer's and Seller's Guide to Radon, United States Environmental Protection Agency, EPA 402/K-24/001, revised March 2024. Device groups, 48 hour minimum, real estate options, interference controls and checklist. Retrieved 21 November 2026.
- EPA Consumer's Guide to Radon Reduction, United States Environmental Protection Agency, EPA 402/K-10/005, 2025. Post-mitigation test window and retest interval. Retrieved 21 November 2026.
- EPA test kit and professional page, United States Environmental Protection Agency, last updated 10 November 2026. NRPP and NRSB contacts. Retrieved 21 November 2026.
- EPA Map of Radon Zones, United States Environmental Protection Agency, last updated 16 September 2026. Retrieved 21 November 2026.
- EPA radon standards of practice page, United States Environmental Protection Agency, last updated 9 July 2026. Current ANSI/AARST editions. Retrieved 21 November 2026.
- CDC radon testing page, Centers for Disease Control and Prevention, reviewed 26 August 2026. Retrieved 21 November 2026.
- ANSI/AARST MAH-2019, Protocol for Conducting Measurements of Radon and Radon Decay Products in Homes, American Association of Radon Scientists and Technologists: ANSI/AARST MAH section 2, MAH section 3.1, MAH Table 3.3, MAH Table 4-A, MAH section 5.1, MAH Table 5.3, MAH section 6.1.2, MAH section 7, MAH section 7.3 and MAH section 8. The 2019 edition was read because it is openly published; EPA lists MAH-2023 as current. Retrieved 21 November 2026.
- National Radon Program Services kit page, Kansas State University under an EPA cooperative agreement. Kit prices and shipping. Retrieved 21 November 2026.
- Washington State Department of Health kit form, Washington State Department of Health. Retrieved 21 November 2026.
- Wisconsin Department of Health Services radon page, Wisconsin Department of Health Services, last revised 21 October 2026. Retrieved 21 November 2026.
- The disagreeing-results examples are arithmetic on the MAH 7.2.2 rule using example values, computed when this page was built. Our methodology sets out the standing rules.
This page describes published EPA guidance and the ANSI/AARST protocol. State radon programs may set stricter rules; confirm with your state radon office before a test used in a sale.
