Bleach to Water Ratio for Mold: 1 Cup or 1/3 Cup per Gallon?

Illustration: a bucket of water and a scrub brush on a tile floor beside an open window

The short answer

The bleach to water ratio for mold depends on the bottle: CDC’s ceiling is 1 cup of household bleach per gallon of water, while Clorox’s current 7.5% EPA label says 1/3 cup per gallon, about 1,500 ppm. Use it only on hard, nonporous surfaces, keep them wet 10 minutes, mix it fresh, and never add vinegar or ammonia.

How much bleach goes in your spray bottle or bucket?

Pick the percentage printed on your bottle. The EPA-accepted Clorox label 5813-120 sets 1,500 ppm available chlorine for mold, and the CDC mold page sets a ceiling of 1 cup per gallon, which is about 2,940 ppm at the 5.25% strength CDC’s 2005 sheet named.

Bleach dilution calculator

This calculator needs JavaScript. The same results are in the static table directly below it.

Bottle strength 4 cups water, 1,500 ppm 1 gallon water, 1,500 ppm 4 cups water, CDC ceiling (2,940 ppm) 1 gallon water, CDC ceiling (2,940 ppm)
5.25% 6 tsp (30 ml), 1,520 ppm 1/2 cup (118 ml), 1,520 ppm 1/4 cup (59 ml), 2,940 ppm 1 cup (237 ml), 2,940 ppm
6% or 6.05% 5 tsp (25 ml), 1,450 ppm 1/2 cup (118 ml), 1,730 ppm 10 tsp (49 ml), 2,820 ppm 3/4 cup (177 ml), 2,550 ppm
7.5% 4 tsp (20 ml), 1,450 ppm 1/3 cup (79 ml), 1,450 ppm 8 tsp (39 ml), 2,840 ppm 2/3 cup (158 ml), 2,840 ppm
8.25% 3.5 tsp (17 ml), 1,410 ppm 1/3 cup (79 ml), 1,600 ppm 7 tsp (35 ml), 2,760 ppm 1/2 cup (118 ml), 2,380 ppm
Static copy of the calculator, computed from the available chlorine printed on EPA-accepted labels. Amounts round to the nearest kitchen measure at 1,500 ppm and round down at the ceiling, and the ppm shown is for the rounded amount, per the formula in the table further down. Check: per the Clorox dilution chart, its 1,500 ppm mix is 4 teaspoons in 4 cups and 1/3 cup per gallon. Retrieved 2 November 2026.

Why do CDC, FEMA, EPA and Clorox print different ratios?

They are answering different questions at different bottle strengths, often without saying which. CDC’s ceiling of 1 cup traces to a time when, per the CDC 2005 bleach sheet, the bleach was 5.25%. The current EPA record for 5813-120 lists 7.5%, so by this page’s arithmetic the same cup now gives about 4,180 ppm, 2.9 times the label’s own mold mix. That gap is why a bare cup count no longer tells you what you mixed.

Source Mix printed Bleach strength Surface Wet time ppm available chlorine
CDC disaster message on preventing mold, reviewed 26 August 2026 1 cup per gallon Not stated, household liquid bleach Where mold is seen or smelled Not stated 2,940 at 5.25%, 4,180 at 7.5%
CDC mold page, dated 26 September 2024 No more than 1 cup per gallon Not stated, household laundry bleach Hard surfaces Not stated Same as above
CDC 2005 bleach sheet, 28 September 2005 1 cup per gallon Regular unscented 5.25% Floors, stoves, sinks, countertops, tools Not stated, rinse after 2,940
FEMA mold booklet, file dated October 2005 1 1/4 to 1 1/2 cups per gallon, called 10% Not stated Metal, glass, solid wood, plastic At least 10 minutes 3,620 to 4,290 at 5.25%
EPA page on bleach and mold, updated 8 September 2026 No ratio Not applicable Not recommended as a routine step Not applicable Not applicable
EPA-accepted Clorox label 5813-120, 8 July 2024 1/3 cup per gallon 7.5% Hard, nonporous At least 10 minutes 1,500 printed
EPA-accepted Clorox label 5813-114, 28 April 2026 3/4 cup per gallon, or 3/4 cup per 3/4 gallon 6.05% Hard, nonporous 10 minutes, or 5 minutes for the stronger mix 2,570, or 3,380
EPA-accepted CloroxPro label 67619-32, 1 September 2020 1/2 cup, or 3/4 cup, per gallon 8.25% Hard, nonporous 10 minutes, or 5 minutes for the stronger mix 2,400 printed, or 3,510
EPA-accepted Clorox label 5813-1, 9 September 2010 3/4 cup per gallon 5.25% Bathroom surfaces, colorfast exteriors 10 minutes 2,240
University of Illinois Extension, 2025 1 cup per gallon Not stated, regular household Mold cleanup after a disaster Not stated 2,940 at 5.25%
Mississippi State Extension 1/2 cup per gallon Not stated, ultra chlorine bleach Contaminated or soiled surfaces 5 to 10 minutes 1,730 at 6%
Washington State Department of Health 1/4 cup per gallon, optional step Not stated After detergent wash 20 minutes, repeat, 20 minutes 770 at 5.25%
University of Georgia Extension 1 cup with 8 to 10 Tbsp TSP per gallon Not stated Painted wood Not stated 2,940 at 5.25%
ppm is labelled printed where the label states it. Other values are arithmetic on the strength shown, and where the source gives no strength the assumption is named. Retrieved 2 November 2026.

Other Clorox labels run stronger than 5813-120. Per the EPA-accepted 5.25% and 6.05% labels, the mix is 3/4 cup per gallon, and per the 8.25% label it is 1/2 cup, all above 2,200 ppm by the same arithmetic. EPA stands apart: the EPA page on bleach and mold gives no ratio and says a biocide is not recommended as a routine step, and the EPA Mold Cleanup in Your Home page starts with detergent and water.

Illustration: wet glazed tile with dark mold specks on the grout line and a nylon brush on the ledge
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

Is 1 cup per gallon a 1:10 ratio? No, it is 1:16

A US gallon holds 16 cups, so 1 cup per gallon is 1 part bleach to 16 parts water. According to one ranking blog, one cup per gallon is about 1 part bleach to 10 parts water, a slip that shows up in results for this query. The Clorox dilution chart does the same sum correctly: 1/3 cup per gallon is 48 parts water to 1 part bleach.

One part bleach against the water it goes intoONE PART BLEACH AGAINST THE WATER IT GOES INTO1 cup per gallon: 1 part bleach, 16 parts waterA true 1:10 dilution: 1 part bleach, 9 parts water
Each square is one equal part. There are 16 cups in a US gallon, and the 1:10 notation follows the EPA-accepted Clorox label 5813-100, which writes 1 part bleach plus 9 parts water as 1:10. Retrieved 2 November 2026.

The difference is not small. Per the CDC disinfection guideline, a 1:10 dilution of household bleach gives about 5,250 to 6,150 ppm, which is the bottle’s hypochlorite percentage divided by 10. A true 1:10 mix takes about 1.78 cups per gallon of water, nearly double the CDC mold ceiling. The FEMA mold booklet has its own version of this slip: it calls 1 1/4 cups per gallon a 10% solution, which is 7.2% by volume, and 1 1/2 cups is 8.6%.

Forum advice runs wider still. In a 2009 Fine Homebuilding forum thread, posters range from a 1:1 mix to full strength, and none states a bottle percentage. The EPA-accepted Clorox label 5813-1 is blunt in the other direction: do not use the product full strength for cleaning surfaces.

What do 1/3, 1/2, 3/4 and 1 cup per gallon mean at 5.25%, 6%, 7.5% and 8.25%?

Read across for your bottle. Strength is sold in at least four grades: the EPA-accepted Clorox label 5813-1 at 5.25%, the EPA-accepted Clorox label 5813-50 at 6.0%, the EPA-accepted Clorox label 5813-120 at 7.5% and the EPA-accepted CloroxPro label 67619-32 at 8.25%, per EPA records. The percentage on the label decides everything below, and the label’s available chlorine figure is what goes in the sum.

Mix Bleach to water 5.25% bottle 6% bottle 7.5% bottle 8.25% bottle
1/4 cup per gallon 1:64 770 880 1,090 1,210
1/3 cup per gallon 1:48 1,020 1,160 1,450 1,600
1/2 cup per gallon 1:32 1,520 1,730 2,150 2,380
3/4 cup per gallon 1:21.3 2,240 2,550 3,180 3,510
1 cup per gallon 1:16 2,940 3,350 4,180 4,620
1 1/4 cup per gallon 1:12.8 3,620 4,130 5,140 5,690
1 1/2 cup per gallon 1:10.7 4,290 4,890 6,090 6,730
ppm available chlorine, rounded to the nearest 10. Formula, per the percentages printed on the labels: available chlorine % times 10,000, times bleach volume, divided by bleach plus water volume. Available chlorine per the labels is 5.0, 5.7, 7.1 and 7.85%. Per the EPA labels, the same formula lands 1% to 4% below printed values: 1,450 against 1,500 at 7.5% and 1/3 cup, and 2,380 against 2,400 at 8.25% and 1/2 cup.
One cup per gallon, by bottle strength, in ppmONE CUP PER GALLON, BY BOTTLE STRENGTH, IN PPMCurrent Clorox label1,5001 cup, 5.25% bottle2,9401 cup, 6% bottle3,3501 cup, 7.5% bottle4,1801 cup, 8.25% bottle4,620
ppm available chlorine from 1 cup of bleach in 1 gallon of water, computed from label strengths, against the 1,500 ppm printed on the EPA-accepted Clorox label 5813-120. Retrieved 2 November 2026.

How long must the bleach solution stay wet, and how long does a batch last?

Ten minutes for the standard mixes. The EPA-accepted Clorox label 5813-120 says pre-wash the surface, then keep it visibly wet for at least 10 minutes, rinse well and air dry. Its exterior direction says to reapply as needed to keep the area wet. Five minutes appears only with the stronger mixes on the EPA-accepted Clorox label 5813-114 and the EPA-accepted CloroxPro label 67619-32.

Mix a new batch each day. The label says to prepare solutions daily for stability, and University of Illinois Extension says the same. The label’s dilution table warns that strength degrades with age, sunlight and heat, and suggests a chlorine test kit. The CDC disinfection guideline reports hypochlorite solutions in tap water losing up to 40% to 50% of free available chlorine over 1 month, even in closed opaque plastic at 23 degrees C.

Dirt uses it up, which is the reason for the pre-wash. The CDC disinfection guideline lists inactivation by organic matter as a drawback of hypochlorite, and Illinois Extension says soiled surfaces can deactivate the bleach. On water temperature the sources split: Illinois says room-temperature water because hot water deactivates bleach, while the Clorox bathroom direction says warm. Room-temperature water avoids the one thing Illinois warns about.

Illustration: a freshly washed wet patch on a painted concrete basement wall
Generated illustration for Remediation Insider. Not a photograph of a real job, event or property.

Can you put bleach on mold on drywall, wood or fabric?

The labels stop at hard, nonporous surfaces, and the Clorox mold page says bleach is not recommended for treating mold on porous materials. The evidence on why is on our does bleach kill mold page. The EPA-accepted Clorox label 5813-120 also says to avoid applying it in direct sunlight or to unfinished wood, and to rinse quickly if it touches aluminum frames or gutters. Mississippi State Extension adds HVAC systems, metals, fine woods and non-colorfast surfaces to the avoid list.

Fabric needs its own check. The EPA-accepted Clorox label 5813-114 says to avoid bleaching wool, silk, mohair, leather, spandex and non-fast colors. EPA’s line for porous building materials is blunter: ceiling tiles and carpet may have to be thrown away, per the EPA Mold Cleanup in Your Home page.

For contractors: which ratio goes in the scope?

Name the product and its registration number, not a cup count. The EPA-accepted Clorox label 5813-120 states it is a violation of federal law to use the product in a manner inconsistent with its labeling, and the ratios above show that a generic 1 cup per gallon can sit at 2.9 times the mold mix printed on a 7.5% bottle. Ask the supplier which registration number is on the delivered bottle, because EPA records list Clorox Germicidal Bleach at 6.05% under 5813-114 and at 8.25% under 67619-32. Scope and containment for larger jobs are on our DIY mold remediation page.

Can you mix bleach and vinegar to kill mold?

No. The National Capital Poison Center vinegar page says the combination creates highly irritating chlorine gas, and a CDC MMWR report gives the reaction: sodium hypochlorite plus an acid releases chlorine gas and water. Bleach plus ammonia forms chloramines instead, per the same report. The CDC mold page says never to mix bleach with ammonia or other cleaners, and the EPA-accepted Clorox label 5813-120 warns that mixing with ammonia or acids may release hazardous gases. The Clorox mold page names vinegar directly.

Toilet bowl cleaners and rust removers count as acids on the EPA-accepted Clorox cleaner label 5813-105, so a mold spray is not the only risk. Vinegar has its own evidence on our vinegar page. Ammonia has its own on our ammonia page. If gases have formed, the National Capital Poison Center chlorine gas page says to leave the area, breathe fresh air, open windows and doors, and call 1-800-222-1222.

Questions people actually ask

Do you rinse bleach solution off after it kills mold?

Yes, on the labelled directions. The EPA-accepted Clorox label 5813-120 says to rinse well and air dry after the 10 minute wet time, and CDC’s 2005 sheet says to rinse with clean water and let the item dry. Neither source tells you to spray it on and walk away, so plan for a clean water wipe as the last step on every surface you treat.

Is a 10% bleach solution too strong for mold?

It sits above CDC’s ceiling. By the EPA label arithmetic, a true 1 part bleach plus 9 parts water at 5.25% is about 5,000 ppm, against about 2,940 ppm at 1 cup per gallon and 1,500 ppm on the current Clorox label. FEMA’s 2005 booklet says 10%, but the cups it prints are weaker than that, and no Clorox mold direction read here uses it.

How much bleach goes in a 5 gallon bucket for mold?

Fill it partway. Per the Clorox dilution chart, 3 gallons of water take 1 cup of its bleach in a five gallon bucket for the 1,500 ppm mix, with room left to work. Per the CDC ceiling at 5.25% bleach, 3 gallons take no more than 3 cups. Measure both, because the Clorox chart says not to guess.

Does 8.25% concentrated bleach change the ratio?

Yes. The EPA-accepted CloroxPro label 67619-32 sets 1/2 cup per gallon at 10 minutes, printed as 2,400 ppm. Per the same label strength, a full cup is about 4,620 ppm by arithmetic, so a 1 cup habit from 5.25% bottles overshoots the label by almost double. Check the percentage on the back panel of each new bottle.

Does scented or splash-less bleach work for mold?

Check the back panel, not the name. Per the CDC 2005 sheet, the bleach is regular unscented 5.25%, and Illinois Extension says regular unscented household bleach. Look for an EPA Reg. No. and a mold direction with a ppm or a cup count. No number and no mold line means the label gives you no mold mix to follow.

Do you need a mask when cleaning mold with bleach?

CDC’s cleanup guide says to wear an N-95 respirator at a minimum, plus goggles and protective gloves, and EPA says to ventilate and exhaust air outdoors when using a biocide. Fit and filter choice are covered on our N95 mask for mold page.

Sources

  1. CDC disaster message on preventing mold, US CDC, published 15 May 2024, reviewed 26 August 2026. Retrieved 2 November 2026.
  2. CDC mold page, US CDC, dated 26 September 2024. Retrieved 2 November 2026.
  3. CDC 2005 bleach sheet, Cleaning and Sanitizing With Bleach after an Emergency, US CDC, 28 September 2005. Retrieved 2 November 2026.
  4. CDC disinfection guideline, Chemical Disinfectants, Guideline for Disinfection and Sterilization in Healthcare Facilities, US CDC. Retrieved 2 November 2026.
  5. CDC cleanup guide, US CDC. Retrieved 2 November 2026.
  6. The CDC MMWR report, Chlorine Gas Toxicity from Mixture of Bleach with Other Cleaning Products, California, used for the reaction chemistry only. Retrieved 2 November 2026.
  7. FEMA mold booklet, Dealing With Mold and Mildew in Your Flood Damaged Home, FEMA, file dated October 2005. Retrieved 2 November 2026.
  8. EPA page on bleach and mold, Should I use bleach to clean up mold?, US EPA, last updated 8 September 2026. Retrieved 2 November 2026.
  9. EPA Mold Cleanup in Your Home page, US EPA, last updated 4 June 2026. Retrieved 2 November 2026.
  10. EPA-accepted Clorox label 5813-120, accepted 8 July 2024, and EPA record for 5813-120, Clorox Disinfecting Bleach. Retrieved 2 November 2026.
  11. EPA-accepted Clorox label 5813-114, accepted 28 April 2026, Clorox Germicidal and Performance Bleach, 6.05%. Retrieved 2 November 2026.
  12. EPA-accepted CloroxPro label 67619-32, accepted 1 September 2020, CloroxPro Clorox Germicidal Bleach, 8.25%. Retrieved 2 November 2026.
  13. EPA-accepted Clorox label 5813-1, accepted 9 September 2010, Clorox Bleach, 5.25%; EPA-accepted Clorox label 5813-100, accepted 8 December 2017, 8.25%; EPA-accepted Clorox label 5813-50, accepted 3 March 2011, 6.0%; EPA-accepted Clorox cleaner label 5813-105, accepted 24 April 2012. All via EPA. Retrieved 2 November 2026.
  14. Clorox mold page and Clorox dilution chart, The Clorox Company. Retrieved 2 November 2026.
  15. University of Illinois Extension, Make Your Own Bleach Sanitizer, 2025. Retrieved 2 November 2026.
  16. Mississippi State Extension, After a flood, how to clean and disinfect, Mississippi State University Extension. Retrieved 2 November 2026.
  17. Washington State Department of Health, Mold, Washington State Department of Health. Retrieved 2 November 2026.
  18. University of Georgia Extension, Remove Stains From Mildew, Mold, UGA Cooperative Extension. Retrieved 2 November 2026.
  19. National Capital Poison Center vinegar page and National Capital Poison Center chlorine gas page, National Capital Poison Center. Retrieved 2 November 2026.
  20. one ranking blog and 2009 Fine Homebuilding forum thread, read as examples of advice in circulation. Retrieved 2 November 2026.
  21. All unprinted ppm figures are arithmetic computed when this page was built. Our methodology sets out the standing rules, and more mold pages are on the mold hub. Health questions about mold are outside this page: go to EPA, NIH or CDC.

Formulas change. The label on the bottle you are holding governs, including its surfaces and its wet time.