The short answer
Yes, asbestos in brick mortar is possible but poorly documented: OSHA’s rule text names asbestos mortar as a bagged product, yet EPA’s 1985 table of building materials has no masonry mortar row. The documented carriers sit beside the brick: insulating cement at 20 to 100 percent, finishing cement at 55 percent, plaster or stucco at 2 to 10 percent. Only a lab count settles a wall.
Which mortars and masonry cements have an asbestos record, and which only have rumours?
Eight materials meet at a brick wall, and the federal record treats them very differently. EPA's 1985 Purple Book (EPA 560/5-85-024) prints an asbestos content range for the cements around a boiler and for plaster and stucco, but has no row for the portland or lime mortar that bonds face brick. The table sorts each material by the strongest evidence found.
| Material and where it sits | Documented asbestos use | Content in the record | Source |
|---|---|---|---|
| Portland or lime mortar in brick joints | Named as a product in OSHA rule text; no EPA content row | None printed | 29 CFR 1910.1001, paragraph (f)(1)(viii); EPA's 1985 Purple Book, Appendix A; WorkSafe New Zealand's A to Z of asbestos products lists “Mortar” |
| Refractory brick and its setting mortar in boilers and furnaces | EPA says boiler insulation may consist of refractory thermal bricks covered with finishing cement | None printed for the brick | EPA's 1985 Purple Book, section 2.2.3; WorkSafe New Zealand's A to Z of asbestos products lists refractory linings and tiles |
| Insulating (furnace) cement on boilers, pipes and breeching | Appendix A row, used 1900 to 1973 | 20 to 100% | EPA's 1985 Purple Book, Appendix A |
| Finishing cement over boiler or pipe insulation | Appendix A row, used 1920 to 1973 | 55% | EPA's 1985 Purple Book, Appendix A |
| Chimney flue liner joint mortar | No US federal or state record found | None printed | Same finding as our fireplace page; sample it |
| Stucco and exterior render | Appendix A plaster or stucco row; NZ lists cement render and fire rated wall rendering | 2 to 10% | EPA's 1985 Purple Book, Appendix A; WorkSafe New Zealand's A to Z of asbestos products |
| Interior plaster | Same Appendix A row as stucco | 2 to 10% | EPA's 1985 Purple Book, Appendix A |
| Patching compound sanded smooth on interior walls | CPSC ban for units made after 16 January 1978, all units after 11 June 1978 | Spackles 3 to 5% | 16 CFR 1304.4; EPA's 1985 Purple Book, Appendix A |
The pattern is plain once the materials are drawn in place. The heat side of an old house (the boiler, its breeching and the pipes) carries printed percentages from 15 to 100. The weather side carries 2 to 10 percent in stucco. The ordinary brick joint in between is the one place EPA printed nothing. Firebrick mortar gets the same finding on our page about an asbestos fireplace.
Rung 1: does 29 CFR 1910.1001 really name asbestos mortar?
Yes, in one sentence. Paragraph (f)(1)(viii) of 29 CFR 1910.1001, headed “Particular products and operations”, reads: “No asbestos cement, mortar, coating, grout, plaster, or similar material containing asbestos, shall be removed from bags, cartons, or other containers in which they are shipped, without being either wetted, or enclosed, or ventilated.” The same wording appears in the 1972 version of the standard reprinted in EPA's 1985 Purple Book, with a 5 fibre per cubic centimetre limit.
What that sentence proves is narrow. OSHA wrote a handling rule for dry asbestos mortar arriving in bags at a workplace, so the product category existed. It does not say how common it was, which years it sold, or whether it went into houses. A figure that circulates in guides online, that 90 percent of US mortar mixes held asbestos before the 1980s, cites no survey, and no EPA, OSHA or CPSC page opened for this article supports it.
Overseas regulators list mortar more directly. WorkSafe New Zealand's A to Z of asbestos products names “Mortar”, “Asbestos cement render, plaster, mortar and coursework”, “Fire-rated wall rendering (containing asbestos with mortar)”, refractory linings and refractory tiles. That list covers New Zealand building stock, so treat it as proof the products were made somewhere, not as a US rate.

Rung 2: what percentages did EPA print in 1985 for cement, plaster and stucco?
Appendix A of EPA's 1985 Purple Book is the closest thing to a federal content table for building products. Of the 6 rows that sit near brickwork, 3 top out at 50 percent or more, and all of those are boiler or sheet products, not a joint between bricks.
| Generic name (EPA 1985) | Asbestos percent | Dates of use |
|---|---|---|
| Insulating cement | 20 to 100 | 1900 to 1973 |
| Finishing cement | 55 | 1920 to 1973 |
| Flat cement sheet | 40 to 50 | 1930 onward |
| Magnesia cement | 15 | 1926 to 1950 |
| Plaster or stucco | 2 to 10 | start unknown, onward |
| Spackles | 3 to 5 | 1930 to 1975 |
The same book explains why a boiler room is the likely place to find an asbestos cement on masonry. Section 2.2.3 says boiler insulation “may consist of thermal bricks (refractory) or asbestos insulating blankets, and is usually covered with finishing cement”. A grey skim over the brick around a boiler door or on breeching is that 55 percent family, not mortar. Stucco and plaster get their own pages: stucco asbestos and asbestos in plaster.
One product that looks like mortar has a firm federal date. 16 CFR 1304.4 bans consumer patching compounds with intentionally added, respirable free form asbestos made after 16 January 1978, and all such compounds after 11 June 1978. 16 CFR 1304.3 defines them as mixes of talc, clays, casein, ground marble or mica sold dry or as paste, and the ban covers compounds sanded smooth on interior walls and ceilings. A tuckpointing mortar is not in that definition.
Rung 3: is old brick mortar presumed asbestos under 29 CFR 1926.1101 if built before 1981?
No. 29 CFR 1926.1101 defines presumed asbestos containing material (PACM) as “thermal system insulation and surfacing material found in buildings constructed no later than 1980”. Surfacing material means material sprayed or troweled on, such as acoustical plaster or fireproofing. A bed joint between bricks is neither, so OSHA does not presume it.
Two clauses still pull mortar in. Paragraph (k)(1) adds that if a building owner or employer “has actual knowledge, or should have known through the exercise of due diligence, that other materials are asbestos-containing, they too must be treated as such.” And insulating or finishing cement on a boiler or breeching is thermal system insulation, which is presumed in any building built by 1980. A presumption is rebutted under paragraph (k)(5) only by an AHERA inspection or bulk samples collected by an accredited inspector or a CIH (industrial hygienist).
Rung 4: how a lab tells if mortar has asbestos, and why the line sits at 4 points in 400
Colour, hardness and age cannot answer it. CPSC's Asbestos in the Home guide says “You can’t tell whether a material contains asbestos simply by looking at it, unless it is labeled.” The test is polarized light microscopy (PLM) under EPA/600/R-93/116, the July 1993 EPA method whose introduction lists plasters and cementitious products among the bulk materials it covers.
The legal line is 1 percent. Both 29 CFR 1926.1101 and 40 CFR 61.141 define asbestos containing material as more than 1 percent asbestos. A lab usually estimates that visually; 40 CFR 61.141 adds that if a result is under 10 percent by any other method, the content must be checked by point counting.
Point counting is where low mortar results get decided. EPA/600/R-93/116 suggests a minimum of 400 counts per sample and says the result is a projected area percent, which cannot be converted to a weight percent without the specific gravities of each component. Labelled calculation: one asbestos point in 400 is 0.25 percent, so a sample needs more than 4 hits to cross 1 percent. A report of “trace” or “under 1 percent” means asbestos was seen but counted at or below that line.
Ask for each layer to be reported on its own. EPA's 1 August 1994 Federal Register advisory says the 1993 method directs labs to analyse “individual strata or layers and report a single result for each layer”, where the 1982 method allowed one number across all of them. A sample that takes mortar, a parge coat and a paint skin in one chip should come back as three results. The same advisory notes PLM may miss fibres thinner than 0.25 micrometres, and the 1993 method adds directions for transmission electron microscopy (TEM) to find them.
CPSC's Asbestos in the Home guide says to send samples to a lab accredited by NVLAP at the National Institute of Standards and Technology, and EPA's homeowner asbestos page says taking samples yourself is not recommended. How to read an NVLAP report is set out under asbestos testing lab. Who samples, and what a survey covers, sits under asbestos inspection.

Who may sample mortar in a house, and how many samples does a wall need?
For a detached single family home, EPA's homeowner asbestos page says federal law does not require the people who inspect, repair or remove asbestos material to be trained and accredited, though some states and localities do. EPA still advises that a trained and accredited professional take samples before remodelling, and that state agencies hold the current lists.
The federal sampling counts come from schools. Per the AHERA rule, 40 CFR 763.86 requires at least 3 samples per homogeneous area of surfacing material up to 1,000 square feet, 5 up to 5,000, and 7 above that. For nonfriable material such as hard mortar it asks only for samples “in a manner sufficient to determine” the result. Each original mortar campaign, each repointing campaign and each patch is a separate homogeneous area, so ask the inspector to sample them separately.
Questions worth putting to an inspector before the visit: which method the lab uses (EPA/600/R-93/116 or the 1982 method), whether results come back per layer, whether results under 10 percent are point counted, and what the state’s own sampling and notification rules require.
Is crumbling asbestos mortar Category II or regulated under 40 CFR 61.141?
Hard, intact mortar that tests above 1 percent fits 40 CFR 61.141‘s Category II nonfriable ACM: any material other than packings, gaskets, resilient flooring and asphalt roofing that “when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure”. Mortar that sands away under a thumb is friable asbestos material instead.
Category II becomes regulated asbestos containing material (RACM) when it “has a high probability of becoming or has become crumbled, pulverized, or reduced to powder” in the demolition or renovation. Grinding out joints or knocking down a wall is the textbook case.
Under 40 CFR 61.145, an owner or operator must thoroughly inspect the affected part of a facility for asbestos, including Category II material, before demolition or renovation starts. 40 CFR 61.141 defines a facility to exclude residential buildings with 4 or fewer dwelling units, so a house or duplex usually sits outside the federal rule, while state and local air agencies may still cover it.
For masons: is repointing confirmed asbestos mortar OSHA Class II or Class III work?
29 CFR 1926.1101 defines Class II work as “the removal of ACM which is not thermal system insulation or surfacing material”, and Class III as “repair and maintenance operations, where ACM, including TSI and surfacing ACM and PACM, is likely to be disturbed”. Raking out a whole elevation of tested asbestos mortar reads as removal. Cutting out a few joints to repair a crack reads as repair. Removing insulating or finishing cement from a boiler is removal of TSI, which the same section puts in Class I.
The bagged product rule in 29 CFR 1910.1001 still matters on a restoration job. Any old stock of dry asbestos mortar, grout or cement found in a building must be wetted, enclosed or ventilated before it leaves the bag. Chimney rebuilds and relines belong to our sister site theroofingbrief.com. Flue pipe has its own page: asbestos flue pipe. The six regulated minerals a lab report names are listed under types of asbestos.
Out of scope here: health effects of exposure. For those, read EPA’s asbestos pages, starting with EPA's homeowner asbestos page. This article covers materials, records, rules and testing only.
Questions people actually ask
Is it okay to live in a house with asbestos mortar?
EPA's homeowner asbestos page says material in good condition that will not be disturbed should be left alone, and that such material generally will not release fibres. CPSC prints the same advice in capitals. The concern starts when mortar is crumbling, being raked out, drilled or demolished, which is when EPA advises sampling first.
What does asbestos brick or asbestos mortar look like?
Like any other grey or buff mortar. CPSC says a material cannot be identified by looking unless it is labeled, so a photo cannot confirm it either. The visual clue that matters is location: a smooth cement skim on a pre 1973 boiler matches EPA’s 55 percent finishing cement row.
What does asbestos cement look like?
In EPA's 1985 Purple Book, asbestos cement means portland cement products such as flat sheet at 40 to 50 percent, corrugated sheet at 20 to 45 percent and siding shingles at 12 to 14 percent. They are thin, hard, grey boards and shingles, not a joint between bricks. CPSC's Asbestos in the Home guide says cement sheets may protect walls and floors around wood burning stoves.
Is the brick itself likely to contain asbestos?
Appendix A of EPA's 1985 Purple Book has no row for clay face brick or concrete block. The brick evidence is narrower: EPA says boiler insulation may use refractory thermal bricks, and WorkSafe New Zealand's A to Z of asbestos products lists refractory linings and tiles. Ordinary red brick in a wall is not on any federal list opened for this article.
Can a home test kit tell if mortar has asbestos?
A mail in kit is a sampling kit; the answer still comes from a lab. CPSC's Asbestos in the Home guide says to use a lab accredited by NIST’s NVLAP program, and EPA advises against sampling yourself. If you use one, ask whether the lab follows EPA/600/R-93/116 and reports each layer separately.
Sources
- 29 CFR 1910.1001, OSHA general industry asbestos standard, paragraph (f)(1)(viii), via Legal Information Institute, Cornell Law School. Retrieved 17 November 2026.
- 29 CFR 1926.1101, OSHA construction asbestos standard, paragraphs (b), (k)(1) and (k)(5), via Legal Information Institute. Retrieved 17 November 2026.
- EPA's 1985 Purple Book, US Environmental Protection Agency, “Guidance for Controlling Asbestos-Containing Materials in Buildings”, EPA 560/5-85-024, June 1985, section 2.2.3, Appendix A and the reprinted 1972 text of 29 CFR 1910.1001. Retrieved 17 November 2026.
- EPA/600/R-93/116, US Environmental Protection Agency, Office of Research and Development, “Method for the Determination of Asbestos in Bulk Building Materials”, July 1993, sections 1.0, 2.2.2 and 2.2.5.2.2. Retrieved 17 November 2026.
- EPA's 1 August 1994 Federal Register advisory, US Environmental Protection Agency, “Advisory Regarding Availability of an Improved Asbestos Bulk Sample Analysis Test Method”, OPPTS-62136, hosted by the Connecticut Department of Public Health. Retrieved 17 November 2026.
- 40 CFR 61.141 and 40 CFR 61.145, asbestos NESHAP definitions and demolition and renovation standard, via Legal Information Institute. Retrieved 17 November 2026.
- 40 CFR 763.86, AHERA sampling rule, via Legal Information Institute. Retrieved 17 November 2026.
- 16 CFR 1304.4 and 16 CFR 1304.3, Consumer Product Safety Commission ban of consumer patching compounds containing respirable free form asbestos, via Legal Information Institute. Retrieved 17 November 2026.
- CPSC's Asbestos in the Home guide, US Consumer Product Safety Commission. Retrieved 17 November 2026.
- EPA's homeowner asbestos page, US Environmental Protection Agency, “Protect Your Family from Exposures to Asbestos”, last updated 25 June 2026. Retrieved 17 November 2026.
- WorkSafe New Zealand's A to Z of asbestos products, WorkSafe New Zealand, “A to Z of products that may contain asbestos”. Retrieved 17 November 2026.
- The point count step (1 point in 400 equals 0.25 percent) is arithmetic on the 400 count minimum in EPA/600/R-93/116. No figure on this page was estimated or invented. Our methodology sets out the standing rules. More rules pages: standards.
Asbestos rules differ by state and city. Before raking out, drilling or demolishing old masonry, ask your state or local air agency which sampling, notification and contractor rules apply to your building.
